Jump to content

Chefs first AR build

Chef

By Chef,
in Guns and Rifles and Discussions

 Share

Recommended Posts

  • Replies 138
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Popular Posts

Chef
Chef

So after the Sullivan county coyote contest and hunting with the jerkman for the weekend I decided it was time for me to build my first AR, it is going to be a dual purpose gun built for Predator hunt

Chef
Chef

Sent from my iPhone using Tapatalk

crappyice
crappyice

I’m still waiting for your charcuterie thread and you start building a scary gun!!! Wtf man!!! Put your apron on and get back in the kitchen!!!! Sent from my iPhone using Tapatalk

Five Seasons Grand Master

Five Seasons

Posted
Posted
5 minutes ago, moog5050 said:

https://www.google.com/amp/s/www.thetruthaboutguns.com/the-truth-about-barrel-length-muzzle-velocity-and-accuracy/amp/

just an example

interesting. It's like if there weren't legal reasons for it, we'd all just hunt with sawed off rifles... although i do like some weight and balance. I think some rifles are too light to balance well. Wonder how this applies to shotgun ballistics too.

Link to comment
Share on other sites
moog5050 Mentor

moog5050

Posted
Posted
28 minutes ago, Belo said:

interesting. It's like if there weren't legal reasons for it, we'd all just hunt with sawed off rifles... although i do like some weight and balance. I think some rifles are too light to balance well. Wonder how this applies to shotgun ballistics too.

Velocity still matters in precision shooting as a minor error in yardage estimation and holdover/doping are less critical.   But my research basically suggested that a short barrel is just as “accurate” as a long barrel.  

Link to comment
Share on other sites
Marion Proficient

Marion

Posted
Posted

Right!


Sent from my iPhone using Tapatalk
You also need to match your gas system to the barrel you have. Likely it will already have the port for mid length, rifle, carbine, etc. And you'll have to match your buffer tube and weight to such. But I'm sure you already have that covered.

Sent from my SM-G935V using Tapatalk

  • Like 1
Link to comment
Share on other sites
Chef Grand Master

Chef

Posted
  • Author
Posted
You also need to match your gas system to the barrel you have. Likely it will already have the port for mid length, rifle, carbine, etc. And you'll have to match your buffer tube and weight to such. But I'm sure you already have that covered.

Sent from my SM-G935V using Tapatalk


For now It’s rifle length and I got the correct buffer, I’m working on picking a gas block now. I’m thinking a bleed off adjustable especially since I went with the low mass bolt carrier


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
Chef Grand Master

Chef

Posted
  • Author
Posted
See....you start this project and now neglect YOUR MEAT!!!! Fridge goes, no updates on stuffing or cooking temps...Cuomo is right...guns are bad!


Sent from my iPhone using Tapatalk

Lol it’s in my basement fridge getting stuffed and smoked tonight


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
moog5050 Mentor

moog5050

Posted
Posted
15 hours ago, Chef said:


Most of it seems to be easy, the front pivot pin however is a pain in the ass I need to
Buy another detent tomorrow


Sent from my iPhone using Tapatalk

Lol.  I hate pulling that pin.   Use a pick to push detent in while sliding in the pin.  Pulling it out is more of a pain!   Took me more than an hour and using two picks to swap that front pin a couple of weeks ago.  

Link to comment
Share on other sites
Chef Grand Master

Chef

Posted
  • Author
Posted
Lol.  I hate pulling that pin.   Use a pick to push detent in while sliding in the pin.  Pulling it out is more of a pain!   Took me more than an hour and using two picks to swap that front pin a couple of weeks ago.  

Yea I can’t even imagine pulling it, I actually got another detent today and got it on my first try about to post pics of the finished lower


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
TACC Collaborator

TACC

Posted
Posted
So I don’t know what possessed me to do this but I went with a low mass bolt carrier group, are any of you running adjustable gas blocks if so which ones


Sent from my iPhone using Tapatalk
The only AR's I have running adjustable gas blocks are ones with suppressors, but I live in Florida, non suppressed 16,18, and 20 inch never needed.

Sent from my SM-G965U using Tapatalk

  • Like 1
Link to comment
Share on other sites
Chef Grand Master

Chef

Posted
  • Author
Posted
The only AR's I have running adjustable gas blocks are ones with suppressors, but I live in Florida, non suppressed 16,18, and 20 inch never needed.

Sent from my SM-G965U using Tapatalk


It’s not that it is needed it’s more that with the low mass bolt carrier I can turn the gas down and get less recoil. Most AR’s are seriously over gassed


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites
moog5050 Mentor

moog5050

Posted
Posted
3 hours ago, Chef said:

So I don’t know what possessed me to do this but I went with a low mass bolt carrier group, are any of you running adjustable gas blocks if so which ones


Sent from my iPhone using Tapatalk

I think if you run a low mass bcg you also need a lighter buffer spring and the adjustable gas block.  Supposed to reduce recoil but I also think they tend to be more finicky.   Hope it works for you but on a 224 the recoil is nothing anyways so you may want to just go with a standard bcg and avoid the tuning hassle. 

  • Like 1
Link to comment
Share on other sites
moog5050 Mentor

moog5050

Posted
Posted
2 minutes ago, Chef said:


It’s not that it is needed it’s more that with the low mass bolt carrier I can turn the gas down and get less recoil. Most AR’s are seriously over gassed


Sent from my iPhone using Tapatalk

You can tell by the ejection if it’s over gassed.  It will chip up the ejection port if over gassed.  90 degree ejection is good (except for the guy to your right at the range lol).  

  • Like 3
Link to comment
Share on other sites
Chef Grand Master

Chef

Posted
  • Author
Posted
I think if you run a low mass bcg you also need a lighter buffer spring and the adjustable gas block.  Supposed to reduce recoil but I also think they tend to be more finicky.   Hope it works for you but on a 224 the recoil is nothing anyways so you may want to just go with a standard bcg and avoid the tuning hassle. 

Yea I probably shouldn’t have done it, but from all the reading I have done it’s all about reciprocating mass so one could always just use a heavier buffer


Sent from my iPhone using Tapatalk
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing   0 members

    No registered users viewing this page.

×
×
  • Create New...