ELMER J. FUDD

High fence is the asterisk of hunting record books. Good job!

Every kid gets a trophy.

So....4SW = Mr. B?

http://static.schneider-electric.us/docs/Circuit Protection/Miniature Circuit Breakers/0110DB0301.pdf Data Bulletin 0110DB0301R05/11 05/2011 Replaces 0110DB0301R03/11 03/2011 Oily Residue Found in Electrical Distribution and Control Equipment © 2003–2011 Schneider Electric All Rights Reserved ™ Introduction Customers are concerned about oily residues found inside electrical distribution and control equipment. They come to Schneider Electric and other electrical equipment manufacturers seeking answers to what it is, possible effects, and what can be done to eliminate it. Oily Residue Tests have shown that the oily residue is actually the plasticizer that is a component of the resin used to make the thermoplastic PVC wire insulation. The plasticizer is added by the wire manufacturer to make the insulation more flexible. Research1 has shown that elevated temperatures and humidity can destroy the relatively weak chemical bond between the plasticizer and the PVC. Given sufficient heat and time, the plasticizer can separate from the PVC wire insulation. Once the plasticizer begins to separate, the process will continue. Unless prevented by an outer jacket of nylon, such as with THHN for example, the plasticizer can exude through the outer surface of the insulation. The plasticizer can also migrate along the stranded wire of the conductor to the end of the insulation via capillary action, and possibly enhanced by a process known as “electroendosmosis”.2 Why does the plasticizer separate from the insulation? Other than having some relation to elevated temperature and humidity, the electrical wire and cable manufacturers do not completely understand why this phenomenon occurs in some installations and not others. Effects of the Oily Residue (Plasticizer Separation) on Electrical Equipment When the plasticizer separates from the PVC insulation, several undesirable effects can occur: • Wire insulation can become hard and brittle. The purpose of the plasticizer is to keep the insulation flexible. • Oily residue (plasticizer) on surfaces of electrical equipment and electrical components can reduce the life of the products and cause performance issues similar to other foreign contaminates like dust, dirt, water, condensation, hydrocarbon sprays or compounds, etc. Recommended Action Schneider Electric recommends that inspection for oily residue (plasticizer separation) be added to your routine inspection and maintenance activities. If oily residue is found: • Do not try to clean the surfaces • Make sure the oily residue is not from the lubricant applied to the wires to facilitate pulling wires through the conduits into the electrical equipment. — Oily residue caused by plasticizer separation is normally found at the ends of the wires where they are stripped for connections etc. — Lubricant applied for pulling activities is normally on the outer surfaces of the insulation. • If you suspect that the oily residue is caused by plasticizer separation, contact the wire manufacturer that supplied the wiring to your contractor. • If oily residue (plasticizer) contamination is found on the surfaces of the electrical equipment and components, the equipment and components are probably damaged. Since there is no practical way to inspect the insulators, etc. in the equipment or the internal parts of the components, Schneider Electric recommends that the contaminated parts of the electrical system be replaced. 1 Peter Wronski, “Exudation of Plasticizers from PVC Insulation Components” presented to the IEEE PSC-ICC Committee on 10/31/2000. 2 National Electrical Code, 2011 Edition, Informational Note for section 310.10. Oily Residue Found in Electrical Distribution and Control Equipment 0110DB0301R05/11 Data Bulletin 05/2011 Electrical equipment should be installed, operated, serviced, and maintained only by qualified personnel. No responsibility is assumed by Schneider Electric for any consequences arising out of the use of this material. Square D™ and Schneider Electric™ are trademarks or registered trademarks of Schneider Electric. Other trademarks used herein are the property of their respective owners. Schneider Electric USA, Inc. 3700 Sixth St SW Cedar Rapids, IA 52404 1-888-778-2733 www.schneider-electric.us 2 © 2003–2011 Schneider Electric All Rights Reserved FAQs Q I have found an “oily” appearing substance on some of the insulators, circuit breakers, terminal blocks, etc. on some of my electrical equipment. What is this stuff? A See the explanation under “Oily Residue”. Q I have also found that some of the insulators in my electrical equipment have deteriorated, or are falling apart. Why is this, and what is causing it? A The plasticizer used in the manufacturing of the wire insulation is typically a hydrocarbon based petroleum derivative. This type of petroleum derivative will cause deterioration of some types of insulating materials commonly used by manufacturers of electrical equipment. Q Why is the “oily” plasticizer coming out of the wire insulation? A We suggest you contact the wire manufacturer for more information. Based upon reports to us, the problem seems to be more prevalent with circuit wires running up a distance above the electrical equipment. Longer runs of wire also seem to experience the greatest loss of the plasticizer. Heat and humidity tend to accelerate the loss of the plasticizer. Q Why does the “oily” substance appear only in the equipment and not on the surface of the wires? A Typical wire insulation is THHN or THWN. This type of wire insulation has an outer jacket of nylon. The plasticizer cannot migrate or penetrate through the nylon jacket so it runs down the strands of the wire until it reaches a point where it can escape. This point is normally where the wire insulation has been stripped away from the conductors. Q Is it typical for wire to lose the plasticizer such as we are seeing? A No, to our knowledge that does not seem to be typical; however the wire manufacturer should be contacted for more specific information. Q How does the “oily” substance get all over the circuit breakers, insulators, and other parts of the electrical equipment? A The plasticizer will tend to continue to migrate over other parts through surface tension. Q What should I do if I discover this condition of “oily” substance on or in my electrical equipment? A Follow the “Recommended Action” section of this Bulletin (above).

I've seen old boxes or a balast have what looks like oil. The balast in a flourescent tube light fixture will do this. In a box it's from old electrical tape I think. Post pix please.

I predict a very long, productive thread.

Stand up has to be a super jet. Sit down's, I prefer the 3 person, err...uh... 2 woman 1 man vessel.

Gonna need more characters. Lol.

Go for it. Support her if you can. It's a good resume builder for college. Might even lead to a scholarship one day.

https://www.usconcealedcarry.com/potentially-fearing-competition-national-rifle-association-disinvites-us-concealed-carry-association-annual-meeting-exhibits/ The United States Concealed Carry Association (USCCA) today announced that the National Rifle Association (NRA) has disinvited the organization from its 2017 Annual Meetings & Exhibits and the 2018 Great American Outdoor Show because of “concerns regarding its programs.” The move shocked the leadership of the USCCA because they were given less than two weeks notice that they had been banned from the annual show, even though they had attended for the past several years. This decision also came as a surprise because over the past two months, the leadership from the NRA and the USCCA met twice to discuss the shared goal of the two organizations in support of the Second Amendment. In a note sent to millions of USCCA supporters, Founder and President Tim Schmidt said that even though the NRA might be fearing the competition, USCCA will still support the NRA’s efforts to protect the Second Amendment. “I’d be lying if I said I wasn’t a little perplexed myself. The truth is, I don’t really know the motive behind the NRA’s move. I mean, the USCCA has ALWAYS had a great relationship with the NRA. And the way I see it, we’re all in this together,” Schmidt said. “If I had to guess, I’d say that perhaps this is a strategic business maneuver,” added Schmidt. “I mean, the concealed carry market has really exploded over the last decade — just look at how long the USCCA has been around! Maybe the NRA recognizes us as the frontrunner in providing the absolute best education, training and self-defense insurance in the industry. And perhaps they’re starting to see us less as a partner and more as a competitor.” “As much as it sort of stings that we got ‘booted’ from the NRA Show, I believe that this sort of competition is a good, healthy and even exciting thing — especially from a goliath like the NRA.” “Whether or not the NRA supports us, we will continue to support them,” Schmidt said. “We will continue to believe in their mission. We will continue to respect the historical significance of what they have done to preserve and protect our God-given rights. And we will always support their legislative and lobbying efforts. I personally will continue to donate to the NRA as a proud Lifetime Member.” Thoughts?

Did you know there have been tracking cookies for years now? The ads you see here can get your history and such. It's just data mining. What are you hiding? Don't worry, you won't get flyers for leather muzzles and whips in the mail. Lol.

I'll be there signing autographs and taking pictures. Meet and greet is $2500 per person.

Pardon the thread drift, but we also need more minorities involved in hunting.

Let's go grab a snack!

Got thisth sthweet new holsthter and a case of pbr.

Uptown, Hey buddy. Let's meet up and talk hunting and politics. I'm just across the river from you. You can come over here if you want and hunt some of my private land spots. I just know it'll be memorable for one of us. Hope to here from ya soon! Your Pal, Elmer

The squirrel ninja clan is in full effect.

It's far away and plus the store sucks. They can keep the 25 bucks. I'm not done with them yet...

Well, I tried to find out, but my wife had very strong opinions, yet zero elaboration on why certain curtains go to the floor or just below the window. I'm now sleeping on the couch tonight.

This was in May. Feels like it was a few months ago. Busy year. Just want everyone to know especially with hunting season almost here. I called several times and never get a manager. Always conveniently busy. The people answering the phone won't take my info and insist i come in. They also say the card is still in the register. Lol. They are stonewalling because they are all in on it IMO.